Brick Paver Installation & Edging



Staging of product

A lot of paver projects will differ depending on gain access to, site conditions, task size and of course, the weather condition. These situations can have a total impact on your task from a timing stand point. Careful factor to consider should be required to identify the time to start the paver installation. Constantly try to avoid any traffic or decrease on the prepared locations.

The supervisor or project supervisor should always have the products (sand/ pavers) distributed around the job site for easy and effective installations. Paver pallets/bundles must be placed in a manner not to hinder the paver installation. The proper pallet/bundle placement can make the actual task installation much easier and quicker by decreasing the total labor of handling the material.

Brick paver patterns

Pavers can be positioned in many different patterns depending on their shape. Each paver shape will usually have several different hatch patterns that are supplied by the manufacturer.

Contractors need to take into factor to consider the traffic weight loads on their paver tasks. In most applications worldwide, it has actually been revealed that pavers laid in a herringbone pattern have actually performed properly.

Pavers that are 60 mm (2 - 3/8 in) density appropriate for pedestrian applications. Pavers that are going to be used in industrial or commercial applications should be 80 mm (3 - 1/8 in) in thickness.

Reference/starting point for brick paver installation

There are a variety of conditions that figure out the beginning point of a paver project.

When starting to install pavers it is best to snap a real straight chalk line on the surface of the bed linen sand or pull a real straight string line above the surface of the bedding sand at the finished elevation of the pavers This will help as a guide for preserving straight joint lines and will likewise permit the installer to make changes in the alignment of the pavers.

Buildings and concrete curbing are typically not straight and must not be utilized for developing straight joint lines. The usage of string lines is necessary to figure out the true straightness of the edge. As the paver installation progresses, the string lines will help reduce the need for little trim pieces.

Joint width in between pavers need to be in between 1/16 and 3/16 in (2 and 5 mm ). There are some pavers with spacer bars on their sides. These will maintain a minimum joint width and allow the bedding and jointing sand to enter between each paver. Pavers with spacer bars are typically not laid in snug versus each other since a string line will provide consistent joint spacing.

Installation of brick pavers.

One of the most widely used methods for the installation of pavers is hand installation of each paver. It is best to install a single row of pavers along one of the true straight lines that you have actually pulled or above the bed linen sand. The best technique is to place a paver versus another one and let it slide down into the bedding sand.

When setting up pavers on a steep grade, they must be set up at the base of the grade going uphill. This will avoid the pavers from creeping as they are being laid.

On large industrial and commercial applications, hand laying pavers would not be cost effective due to the labor strength. The best way for setting up pavers on big jobs is to install them mechanically. The use of a mechanical laying device can set up roughly 6000 - 7000 sq ft a day. There are a couple products a contractor must consider before setting up pavers mechanically:

1.) Mechanical installers are just efficient in setting up pavers in particular patterns.

2.) The contractor should make sure that the producer is capable of manufacturing and bundling pavers in the preferred pattern on the pallets for simple mechanical installation.

Poor color mixing might result in an irregular looking installation. A lot of manufacturers are constant with color mixing on each package of pavers, however it is the contractor's responsibility to make sure correct blending in the field.

Cutting treatments for brick pavers.

Contractors normally have 2 ways of cutting pavers. When cutting pavers damp, it will help minimize dust and will lengthen the diamond blades life. The operator of the brick saw ought to always cut the pavers away from the surface area of the paver field when cutting wet, due to the reality that the pavers will produce a slurry that will stain the paver surface.

The brick saw operator needs to always use the appropriate protection that is required for operating a saw, such as eye, ear, breathing and hand security ).

Edging types

Edge restraints play a major function in the overall success of an interlocking pavement installation Edging restraints remove lateral movement of the pavers and hold the pavers tightly together. Particularly at the outer border of the paver application, without an edging restraint, your job is ensured to stop working over time.

There are numerous different edging restraints from which specialists can select. Usually manufactured edge restraints are the most frequently used by specialists. Produced edging restraints can vary from, plastic edging, steel and aluminum, woods or precast concrete and stone. An edging type that is utilized mainly in commercial and commercial applications is poured-in-place concrete curbs. This edging restraint is typically set up by other contractors.

Edging installation.

This could result in Tree Service Del Ray Beach the migration of the bed linen sand and ultimate lateral movement of the pavers. If there is a possibility of losing bed linen sand in between the pavers and the edge restraint, then geo textile fabric is suggested. When a space between the pavers and the edging surpasses 3/8" (10mm), then the area should be filled with cut pavers.

Compaction of brick pavers.

After installation, the pavers need to be compressed. The entire area that is to be compressed should be swept clean of any foreign items and debris that can trigger scratching or scuffing on the surface of the pavers.

It is necessary to have a compactor that can exert between 3000lbs. And 5000 pounds. Of centrifugal compaction force. In addition, it is important that the first compaction occurs prior to any jointing sand has been applied to the pavers. This can trigger a bridging problem and will not enable the joints to be totally filled with jointing sand if jointing sand is used to the pavers before compaction takes place. This can also avoid the pavers from being correctly set into the bed linen sand.

When compacting the pavers, it is suggested that you make a minimum of 2 passes in different directions across the pavers. This will enable the pavers to be effectively embeded in the bedding sand and will force the bedding sand up into the joints from the bottom of the pavers.

The compaction of the pavers is really important to the final performance of the pavers. Failure to do proper compaction can result in contortions and pavement failure with time.


Paver pallets/bundles need to be placed in a manner not to interfere with the paver installation. One of the most commonly utilized approaches for the installation of pavers is hand installation of each paver. The operator of the brick saw need to constantly cut the pavers away from the surface of the paver field when cutting wet, due to the fact that the pavers will produce a slurry that will stain the paver surface area. Edging restraints get rid of lateral motion of the pavers and hold the pavers securely together. When a space in between the pavers and the edging exceeds 3/8" (10mm), then the space ought to be filled with cut pavers.

Leave a Reply

Your email address will not be published. Required fields are marked *